GLAST/LAT > DAQ and FSW > FSW > Doxygen Index > LIM / V1-19-1
Constituent: lim_scp     Tag: mv2304
#include "CLI/CLI_pubdefs.h"
Include dependency graph for LIM_send.h:
This graph shows which files directly or indirectly include this file:
Functions | |
unsigned int | LIM_sendBiasAcdHv (unsigned int arc_id, unsigned int bias) |
Send the Bias-ACD command to set an ARC's HV bias. | |
unsigned int | LIM_sendBiasAcdSaa (unsigned int arc_id, unsigned int bias) |
Send the Bias-ACD command to set an ARC's SAA bias. | |
unsigned int | LIM_sendBiasCal (unsigned int tower_id, unsigned int bias) |
Send the Bias-CAL command. | |
unsigned int | LIM_sendBiasTkr (unsigned int tower_id, unsigned int bias) |
Send the Bias-TKR command. | |
unsigned int | LIM_sendCalStart (unsigned int latc_config, unsigned int lci_config, unsigned int dest) |
Send the Calibration-Start command. | |
unsigned int | LIM_sendConfigGbm (int rep_allowed, int pri_int_allowed, int red_int_allowed) |
Send the Configure-GBM command. | |
unsigned int | LIM_sendConfigHv (int hv_allowed) |
Send the Configure-HV command. | |
unsigned int | LIM_sendConfigPid (int primary) |
Send the Configure-PID command. | |
unsigned int | LIM_sendEpuOff (unsigned int epu_id) |
Send the Power-Off command to disable power from an EPU. | |
unsigned int | LIM_sendEpuOn (unsigned int epu_id, unsigned int pdu_id) |
Send the Power-On command to enable power to an EPU. | |
unsigned int | LIM_sendHoldEnter (void) |
Send the Hold-Enter command. | |
unsigned int | LIM_sendHoldExit (void) |
Send the Hold-Exit command. | |
unsigned int | LIM_sendLatcRecord (unsigned int dest) |
Send the Latc-Record command. | |
unsigned int | LIM_sendLoadShed (void) |
Send the Load-Shed command. | |
unsigned int | LIM_sendMainFeedOnPrimary (unsigned int siu_id, unsigned int pdu, unsigned int pps) |
Send the Main-Feed-On command to enable primary component power. | |
unsigned int | LIM_sendPigRecord (unsigned int dest) |
Send the Pig-Record command. | |
unsigned int | LIM_sendSaaEnter (void) |
Send the SAA-Enter command. | |
unsigned int | LIM_sendSaaExit (void) |
Send the SAA-Exit command. | |
unsigned int | LIM_sendSafeMode (void) |
Send the Safe-Mode command. | |
unsigned int | LIM_sendTemOn (unsigned int tem_id, unsigned int pdu_id) |
Send the Power-On command to enable power to a TEM. | |
int | LIM_setDisplayLevelCmd (int level) |
Set the verbosity level of the LIM command display. | |
unsigned int | LIM_addSyntaxSCP (CLI_Syntax *syntax) |
Add LIM commands to the command-line syntax. |
** CVS $Id: LIM_send.h,v 1.9 2006/03/17 20:41:13 dmay Exp $ **
Defines the interface to the functions found in LIM_send.c.
|
Add LIM commands to the command-line syntax.
|
|
Send the Bias-ACD command to set an ARC's HV bias.
|
|
Send the Bias-ACD command to set an ARC's SAA bias.
|
|
Send the Bias-CAL command.
|
|
Send the Bias-TKR command.
|
|
Send the Calibration-Start command.
|
|
Send the Configure-GBM command.
|
|
Send the Configure-HV command.
|
|
Send the Configure-PID command.
|
|
Send the Power-Off command to disable power from an EPU.
|
|
Send the Power-On command to enable power to an EPU.
|
|
Send the Hold-Enter command.
|
|
Send the Hold-Exit command.
|
|
Send the Latc-Record command.
|
|
Send the Load-Shed command.
|
|
Send the Main-Feed-On command to enable primary component power. This command sends the Main-Feed-On command to enable power using the primary main feed and primary DAB. It also selects the primary paths to the SSR and GBM.
|
|
Send the Pig-Record command.
|
|
Send the SAA-Enter command.
|
|
Send the SAA-Exit command.
|
|
Send the Safe-Mode command.
|
|
Send the Power-On command to enable power to a TEM.
|
|
Set the verbosity level of the LIM command display.
|